How to effectively wax a snowboard

Now, take a bar of wax and rub it lengthwise on the board.

snowboard waxing table

Now you go on to start with the process of waxing your snowboard. Waxing a Snowboard with an Iron The Wax: Ideally your choice of wax should depend on the type of snow that you snowboard on. Step 8 — scrape your board As with edging, it's generally advisable to scrape from nose to tail.

Feel the underneath of the board to ensure the iron is not too hot and the board does not overheat.

Snowboard waxing near me

Iron the base Next, place the iron on the base of the board and move it around in a circular motion. If the snow in you area is slushy and tends to melt, then use a stiff wire brush to stroke the snowboard in a cross-hatch pattern before you apply the wax and then buffing it properly with a hard bristled brush during the final polishing, so that it is sintered. Let us see what you need to do after that. Lastly, use a heavy-duty scouring pad like an abrading 'Green Scotchbrite' or a very mild sandpaper to brush you board with brisk, firm, and short lengthwise strokes. The trick is to get the board nice and warm. Step 6 — spread the wax Take the iron and spread the wax evenly around the board. Spray waxes or paste waxes are perfect. If you're a seasonal veteran or just prefer the DIY method, we've come up with some tips and tricks to help you along the way. We generally suggest waiting minutes. The wax will liquify and pour off of the iron and on to your board. Wipe the board off with the cloth again. Get scraping Once the wax has cooled, hold your plastic scraper at a 45 degree angle and carefully work from nose to tail, scraping off any excess wax. There should be an arrow on the side of the file that indicates the direction it should go. To test the sharpness of the edge, scrape your fingernail over it — your nail will peel if your edge is sharp.

A Heat Gun: Now this is nothing but a blow dryer that has more complex regulators and can be set at much higher temperatures than a normal hair dryer. Press your iron onto your snowboard and start going back and forth along the drip line.

How to effectively wax a snowboard

Hold it width-ways at roughly 45 degrees to the board, so that there is a sharp edge in contact, and begin scraping off the excess wax. When it is hot, hold the wax near the base of the iron and gradually allow the wax droplets to fall on the board in a even, up and down zig-zag pattern lengthwise. Head to the mountains and enjoy your new super fast ride! Waxing a Snowboard Without an Iron The equipment that replaces the iron here is a heat gun. If they are minor slashes, then just take a treated P-tex thermoplastic candle, kindle it, and allow the wax to fill up the gashes. Make sure you run the wax the entirety of the boards length. Step 8 — scrape your board As with edging, it's generally advisable to scrape from nose to tail. We also offer packets of assorted wax, perfect for anyone who likes to travel. Polish the board for 2 minutes with a soft rag. Remember, all you scraping must be lengthwise or you'll damage the board. This will shine up your edges nicely, remove any rust, even out any imperfections made by your file and improve performance very slightly.

The wax will liquify and pour off of the iron and on to your board. If you're a seasonal veteran or just prefer the DIY method, we've come up with some tips and tricks to help you along the way.

When this dries up, use the same sharp chisel to remove all traces of excess wax from the area, with long strokes. Step 6 — spread the wax Take the iron and spread the wax evenly around the board. This will help you to determine whether you have an absolutely flat snowboard as it should be for that ultra perfect gliding experience.

Then take your nylon base brush and give each area 3 or 4 hard strokes, working from nose to tail — this adds structure to your base, which stops suction and allows it to run smoother and quicker. Now apply pressure with the file on the side edge and drag it along the length of the edge.

When your bindings are tightened into your board, the screws can suck minor divots into the base.

how to cold wax a snowboard
Rated 9/10 based on 100 review
Download
How To Wax A Snowboard